The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

Pump Lutz B2 Vario, universal motor110 V with speed control, pump tube PPor stainless steel, 5' PVC braided hose 3/4",Lutz nozzle, hose clamps, wall bracket

Pump Lutz B2 Vario, universal motor110 V with speed control, pump tube PPor stainless steel, 5' PVC braided hose 3/4",Lutz nozzle, hose clamps, wall bracket

Pump Lutz B2 Vario, universal motor110 V with speed control, pump tube PPor stainless steel, 5' PVC braided hose 3/4",Lutz nozzle, hose clamps, wall bracket

Electric motor, pump tube PP sealless, highvolume rotor, Hastelloy C drive shaft, 2" NPT PPbarrel adapter, 3/4" PP nozzle, 8' PVC hose, hoseclamps, PP drum adapter, wall bracket

Electric motor, pump tube PP sealless, highvolume rotor, Hastelloy C drive shaft, 2" NPT PPbarrel adapter, 3/4" PP nozzle, 8' PVC hose, hoseclamps, PP drum adapter, wall bracket

Electric or air driven motor, pump tube PVDFsealless, high volume rotor, Hastelloy C driveshaft, 2" NPT PP drum adapter, 1" PVDF nozzle,7' chemical hose, hose clamps, wall bracket

Electric or air driven motor, pump tube PVDFsealless, high volume rotor, Hastelloy C driveshaft, 2" NPT PP drum adapter, 1" PVDF nozzle,7' chemical hose, hose clamps, wall bracket

Electric or air driven motor, pump tube PVDFsealless, high volume rotor, Hastelloy C driveshaft, 2" NPT PP drum adapter, 1" PVDF nozzle,7' chemical hose, hose clamps, wall bracket

Explosion proof motor ME I 6 or air driven motor MD-2, pump tube stainless steel sealless, high volume rotor, SS driveshaft, 2" NPT drum adapter SS, 2" stainless steel nozzle, 8' conductive chemical tubing with conductive fittings, ground andbonding wires, wall bracket

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

Finish Thompson model M62 drum pump motors are compatible with the following Finish Thompson series drum pumps: HVDP. Model M62 totally enclosed fan cooled (TEFC) IP54 induction motor has an output of 1.5 kilo watts, 60 Hz, 115/230 Volts, single phase, 20/10 full load ampere rating (FLA), 3,450 RPM and a maximum viscosity of 100,000 cP.

Finish Thompson model M66 drum pump motors are compatible with the following Finish Thompson series drum pumps: HVDP. Model M66 air motor has an output of 1.1 kilo watts, 300 to 3,000 RPM, a maximum viscosity of 100,000 cP and is CE certified. Model M66 air motors require 100 psi @ 70 cfm for operation.

Finish Thompson model M3V drum pump motors are compatible with the following Finish Thompson series drum pumps: PF and TB. Model M3V Open Drip Proof (ODP) motor has an input/output of 650/400 Watts, 50/60 Hz, 115 Volts, Variable Speed, 5.6 full load ampere rating (FLA), 3,500 to 10,000 RPM and a maximum viscosity of 500 cP on PF Model and 200 cP on TB Model Pumps. This motor is RoHS and CSA Compliant, has an integral motor overload and comes with a 12 foot cord with plug. Model M3V motor offers quick connection of the motor to the pump tube with a unique collet design eliminating the need for tools. The double wall thermoplastic motor housing reduces noise and vibration.

Finish Thompson model M5V-US drum pump motors are compatible with the following Finish Thompson series drum pumps: PF and TB. Model M5V-US Open Drip Proof (ODP) motor has an input/output of 650/400 Watts, 50/60 Hz, 230 Volts, Variable Speed, 2.8 full load ampere rating (FLA), 3,500 to 10,000 RPM and a maximum viscosity of 500 cP on PF Model and 200 cP on TB Model Pumps. This motor is RoHS and CE Compliant, has an integral motor overload and comes with a 12 foot cord with plug. Model M5V-US motor offers quick connection of the motor to the pump tube with a unique collet design eliminating the need for tools. The double wall thermoplastic motor housing reduces noise and vibration.

Finish Thompson model M5V drum pump motors are compatible with the following Finish Thompson series drum pumps: PF and TB. Model M5V Open Drip Proof (ODP) motor has an input/output of 650/400 Watts, 50/60 Hz, 230 Volts, Variable Speed, 2.7 full load ampere rating (FLA), 3,500 to 10,000 RPM and a maximum viscosity of 500 cP on PF Model and 200 cP on TB Model Pumps. This motor is RoHS and CE Compliant, has an integral motor overload and comes with a 12 foot cord with plug. Model M5V motor offers quick connection of the motor to the pump tube with a unique collet design eliminating the need for tools. The double wall thermoplastic motor housing reduces noise and vibration.

Finish Thompson model S1 drum pump motors are compatible with the following Finish Thompson series drum pumps: EF. Model S1 Open Drip Proof (ODP) motor has an input/output of 230/110 Watts, 60 Hz, 115 Volts, Single Phase, Variable Speed, 2.0 full load ampere rating (FLA), 8,000 to 14,000 RPM and a maximum viscosity of 300 cP. The double wall thermoplastic motor housing reduces noise and vibration.

Finish Thompson model S4 air operated drum pump motors are compatible with the following Finish Thompson series drum pumps: EP. The Model S4 air motor has an output of 400 watts, 300 to 11,000 RPM, a maximum viscosity of 300 cP and is CE certified. Model S4 air motors require 40 psi @ 27 cfm for operation.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

The Sharpe E-series worm gear drive meets low leadroom requirements without sacrificing performance. Standard C-face motor mounting is designed for simple trouble-free installation, with positive registers for repeatable alignment. Efficient "high pressure angle" gearing provides extremely quiet operation and high shock-load capacity. The hallow quill gearbox design uses an oversized tapered roller bearing for long overhung shafts, and requires no flange coupling for assembly. Heat and shock loading is isolated between the motor and gearbox.

The E-series mixers are available in top and side entering designs, with mountings ranging from simple open-tank plate mounts to complex mechanical seal systems. Sizes range from fractional to 75 horsepower. Drive housing is corrosion resistant cast iron. Wetted parts are 316 stainless steel standard. Carbon steel, exotic alloys, or coatings are also available when required.

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants

Fast-Flo pumps are designed to operate at air input pressures up to 180 psi (12 bar, 1.2 MPa) and deliver a smooth, reliable flow. Drum length and stubby models are available for either drum transfer or wall mount siphon feed applications. Ideal for lower viscosity fluids with plate (flat) check options.

Ideal applications and materials for use with Fast-Flo® pumps are:

• Oil Transfer
• Ink Transfer
• Pumping
• Fluid Transfer
• Antifreeze
• Asphalts
• Windshield Washer Fluid
• Motor Oil
• Used Oil
• Hydraulic Fluid
• Oil
• Inks and Colorants